321 lines
8.7 KiB
INI
321 lines
8.7 KiB
INI
# This file allows user to override the factory
|
|
# defaults for the WLAN Driver
|
|
|
|
# Phy Mode (auto, b, g, n, etc)
|
|
# Valid values are 0-12, with 0(Min) = Auto, 12(Max) = 11ax
|
|
# 1 = 11abg, 2 = 11b, 3 = 11g, 4 = 11n, 5 = 11g only, 6 = 11n only
|
|
# 7 = 11b only 8 = 11ac only, 9 = 11ac, 12 = 11ax.
|
|
gDot11Mode=0
|
|
|
|
# UAPSD service interval for VO,VI, BE, BK traffic
|
|
InfraUapsdVoSrvIntv=0
|
|
InfraUapsdViSrvIntv=0
|
|
InfraUapsdBeSrvIntv=0
|
|
InfraUapsdBkSrvIntv=0
|
|
|
|
# Flag to allow STA send AddTspec even when ACM is Off
|
|
gAddTSWhenACMIsOff=1
|
|
|
|
#Enable OBSS protection
|
|
gEnableApOBSSProt=1
|
|
|
|
# Maximum Tx power
|
|
# gTxPowerCap=30
|
|
|
|
# Fragmentation Threshold
|
|
# gFragmentationThreshold=2346
|
|
|
|
# RTS threshold
|
|
RTSThreshold=1048576
|
|
|
|
# WMM Enable/Disable
|
|
WmmIsEnabled=0
|
|
|
|
# 802.11d support
|
|
g11dSupportEnabled=0
|
|
|
|
# DFS Master Capability
|
|
gEnableDFSMasterCap=1
|
|
|
|
ImplicitQosIsEnabled=0
|
|
|
|
gNeighborScanTimerPeriod=200
|
|
gNeighborLookupThreshold=76
|
|
|
|
# Legacy (non-ESE, non-802.11r) Fast Roaming Support
|
|
# To enable, set FastRoamEnabled=1
|
|
# To disable, set FastRoamEnabled=0
|
|
FastRoamEnabled=1
|
|
|
|
#Channel Bonding
|
|
gChannelBondingMode5GHz=1
|
|
|
|
#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds).
|
|
#For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link
|
|
#is idle for last 10 seconds.) For both active and power save clients.
|
|
|
|
#Power save clients: DUT set TIM bit from 10th second onwards and till client
|
|
#honors TIM bit. If doesn't honor for 5 seconds then DUT remove client.
|
|
|
|
#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not
|
|
#success still we try on 11th second if not tries on 12th and so on till 15th
|
|
#second. Hence before disconnection DUT will send 5 NULL frames. Hence in any
|
|
#case DUT will detect client got removed in (10+5) seconds.
|
|
#i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod)..
|
|
|
|
#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and
|
|
#it is period where we send NULL frame.
|
|
#gApLinkMonitorPeriod = 10
|
|
#gGoLinkMonitorPeriod = 10
|
|
|
|
#gApKeepAlivePeriod is time to spend to check whether frame
|
|
#are succeed to send or not. Hence total effective detection time is
|
|
#(gApLinkMonitorPeriod + gApKeepAlivePeriod)
|
|
|
|
# Enable DFS channel roam
|
|
# 0: DISABLE, 1: ENABLED_NORMAL, 2: ENABLED_ACTIVE
|
|
gAllowDFSChannelRoam=1
|
|
|
|
gVhtChannelWidth=2
|
|
|
|
# Set txchainmask and rxchainmask
|
|
# These parameters are used only if gEnable2x2 is 0
|
|
# Valid values are 1,2
|
|
# Set gSetTxChainmask1x1=1 or gSetRxChainmask1x1=1 to select chain0.
|
|
# Set gSetTxChainmask1x1=2 or gSetRxChainmask1x1=2 to select chain1.
|
|
gSetTxChainmask1x1=1
|
|
gSetRxChainmask1x1=1
|
|
|
|
# MCC to SCC Switch mode:
|
|
# 0-Disable
|
|
# 1-Enable
|
|
# 2-Force SCC if same band, with SAP restart
|
|
# 3-Force SCC if same band, without SAP restart by sending (E)CSA
|
|
# 4-Force SCC if same band (or) use SAP mandatory channel for DBS,
|
|
# without SAP restart by sending (E)CSA
|
|
gWlanMccToSccSwitchMode = 3
|
|
|
|
# 1=enable tx STBC; 0=disable
|
|
gEnableTXSTBC=1
|
|
|
|
#Enable/Disable Tx beamformee in SAP mode
|
|
gEnableTxBFeeSAP=1
|
|
|
|
# Enable Tx beamforming in VHT20MHz
|
|
# Valid values are 0,1. If commented out, the default value is 0.
|
|
# 0=disable, 1=enable
|
|
gEnableTxBFin20MHz=1
|
|
|
|
#Enable/Disable SU Tx beamformer support
|
|
gEnableTxSUBeamformer=1
|
|
|
|
# 802.11K support
|
|
gRrmEnable=1
|
|
|
|
# Maximum Receive AMPDU size (VHT only. Valid values:
|
|
# 0->8k 1->16k 2->32k 3->64k 4->128k)
|
|
gVhtAmpduLenExponent=7
|
|
|
|
# Maximum MPDU length (VHT only. Valid values:
|
|
# 0->3895 octets, 1->7991 octets, 2->11454 octets)
|
|
gVhtMpduLen=2
|
|
|
|
#Enable or Disable p2p device address administered
|
|
isP2pDeviceAddrAdministrated=0
|
|
|
|
#Enable VHT on 2.4Ghz
|
|
gEnableVhtFor24GHzBand=1
|
|
|
|
#Maximum number of offload peers supported
|
|
# gMaxOffloadPeers=2
|
|
|
|
# controlling the following offload patterns
|
|
# through ini parameter. Default value is 1
|
|
# to disable set it to zero. ssdp = 0
|
|
# Setup multicast pattern for mDNS 224.0.0.251,
|
|
# SSDP 239.255.255.250 and LLMNR 224.0.0.252
|
|
ssdp=0
|
|
|
|
# RA filtering rate limit param, the current value would not
|
|
# help if the lifetime in RA is less than 3*60=3min. Then
|
|
# we need to change it, though it is uncommon.
|
|
# gRAFilterEnable=0
|
|
gRArateLimitInterval=600
|
|
|
|
# Maximum number of concurrent connections
|
|
gMaxConcurrentActiveSessions=3
|
|
|
|
# Disable/Enable GreenAP
|
|
# 0 to disable, 1 to enable, default: 1
|
|
gEnableGreenAp=0
|
|
|
|
#Enable/Disable LPASS support
|
|
# 0 to disable, 1 to enable
|
|
gEnableLpassSupport=1
|
|
|
|
# Whether userspace country code setting shld have priority
|
|
gCountryCodePriority=1
|
|
|
|
# Enable or Disable Multi-user MIMO
|
|
# 1=Enable (default), 0=Disable
|
|
gEnableMuBformee=1
|
|
|
|
# Enable TDLS External Control. That is, user space application has to
|
|
# first configure a peer MAC in wlan driver towards which TDLS is desired.
|
|
# Device will establish TDLS only towards those configured peers whenever
|
|
# TDLS criteria (throughput and RSSI threshold) is met and teardown TDLS
|
|
# when teardown criteria (idle packet count and RSSI) is met. However,
|
|
# device will accept TDLS connection if it is initiated from any other peer,
|
|
# even if that peer is not configured.
|
|
# 0 - disable
|
|
# 1 - enable
|
|
# For TDLS External Control, Implicit Trigger must also be enabled.
|
|
gTDLSExternalControl=1
|
|
|
|
# Enable support for TDLS off-channel operation
|
|
# 0 - disable
|
|
# 1 - enable
|
|
# TDLS off-channel operation will be invoked when there is only one
|
|
# TDLS connection.
|
|
gEnableTDLSOffChannel=1
|
|
|
|
# VHT Tx/Rx MCS values
|
|
# Valid values are 0,1,2. If commented out, the default value is 0.
|
|
# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
|
|
gVhtRxMCS=2
|
|
gVhtTxMCS=2
|
|
|
|
# VHT Tx/Rx MCS values for 2x2
|
|
# Valid values are 0,1,2. If commented out, the default value is 0.
|
|
# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
|
|
gEnable2x2=1
|
|
gVhtRxMCS2x2=2
|
|
gVhtTxMCS2x2=2
|
|
|
|
#IPA config is a bit mask and following are the configurations.
|
|
#bit0 IPA Enable
|
|
#bit1 IPA PRE Filter enable
|
|
#bit2 IPv6 enable
|
|
#bit3 IPA Resource Manager (RM) enable
|
|
#bit4 IPA Clock scaling enable
|
|
#bit5 IPA uC ENABLE
|
|
#bit6 IPA uC STA ENABLE
|
|
#bit8 IPA Real Time Debugging
|
|
gIPAConfig=0x7d
|
|
gIPADescSize=800
|
|
|
|
# Increase TCL ringsize
|
|
dp_tx_ring_size=3072
|
|
|
|
# Disable HW checksum for legacy modes
|
|
legacy_mode_csum_disable=1
|
|
|
|
# Enable TCP Segmentation Offload
|
|
# 1 - enable 0 - disable
|
|
TSOEnable=1
|
|
|
|
# Enable Generic Receive Offload
|
|
# 1 - enable(default) 0 - disable
|
|
GROEnable=1
|
|
|
|
# Enable HT MPDU Density
|
|
# 4 for 2 micro sec
|
|
ght_mpdu_density=4
|
|
|
|
# Enable flow steering to enable multiple CEs for Rx flows.
|
|
# Multiple Rx CEs<==>Multiple Rx IRQs<==>probably different CPUs.
|
|
# Parallel Rx paths.
|
|
# 1 - enable 0 - disable(default)
|
|
gEnableFlowSteering=1
|
|
|
|
# Enable Rx FISA support
|
|
# 0 - disable(default for non-QCA6490), 1 - enable(default for QCA6490)
|
|
dp_rx_fisa_enable=1
|
|
|
|
# FISA FSE flow table size
|
|
dp_rx_flow_search_table_size=128
|
|
|
|
# Maximum number of MSDUs the firmware will pack in one HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND
|
|
maxMSDUsPerRxInd=8
|
|
|
|
gHandleLatencyCriticalClients=1
|
|
|
|
# RPS map for different RX queues (seperate by spaces)
|
|
# Internally, the nibbles get swapped.
|
|
rpsRxQueueCpuMapList=f7
|
|
|
|
################ Datapath feature set End ################
|
|
|
|
################ NAN feature set start ###################
|
|
|
|
# Enable NAN discovery (NAN 1.0)
|
|
# 1 - enable 0 - disable(default)
|
|
gEnableNanSupport=1
|
|
# Enable NAN Datapath
|
|
genable_nan_datapath=1
|
|
|
|
################ NAN feature set end #####################
|
|
|
|
hostscan_adaptive_dwell_mode=1
|
|
|
|
# Enable/Disable rtt sta mac randomization
|
|
enable_rtt_mac_randomization=1
|
|
|
|
#Enable/Disable SNR monitoring
|
|
gEnableSNRMonitoring=1
|
|
|
|
# HTC Credit count for WMI operation
|
|
# 1 to serialize the WMI commands
|
|
# 0 default works with FW advertised credits, 2 credits usually
|
|
gWmiCreditCount=1
|
|
|
|
# Enable enhanced ACS
|
|
acs_with_more_param=1
|
|
# bits 0-3: rssi weight
|
|
# bits 4-7: bss count weight
|
|
# bits 8-11: noise floor weight
|
|
# bits 12-15: channel free weight
|
|
# bits 16-19: tx power range weight
|
|
# bits 20-23: tx power throughput weight
|
|
# bits 24-31: reserved
|
|
AutoChannelSelectWeight=0x00fafafa
|
|
|
|
# Enable/Disable broadcast TWT
|
|
bcast_twt=1
|
|
|
|
# Enable Runtime PM
|
|
# 0 - RTPM disabled, so CxPC aware RTPM will be disabled as well
|
|
# 1 - RTPM enabled, but CxPC aware RTPM disabled (i.e, Static Runtime PM)
|
|
# 2 - RTPM enabled and CxPC aware RTPM enabled as well (i.e, Dynamic Runtime PM)
|
|
gRuntimePM=2
|
|
gRuntimePMDelay=500
|
|
|
|
active_max_channel_time_6g=60
|
|
passive_max_channel_time_6g=60
|
|
|
|
# Enable broadcast logging to the userspace entities
|
|
gMulticastHostFwMsgs=1
|
|
# Disable packetlog explicitly
|
|
gEnablePacketLog=0
|
|
|
|
# Set IPA bandwidth levels in mbps
|
|
gIPALowBandwidthMbps=100
|
|
gIPAMediumBandwidthMbps=400
|
|
gIPAHighBandwidthMbps=800
|
|
|
|
# Enable wlm_latency_enable feature
|
|
# 0 - disable, 1 - enable(default)
|
|
wlm_latency_enable=1
|
|
spectral_disable=1
|
|
|
|
# This ini is used to give higher priority for 5g scc than dbs.
|
|
# It is bitmap per enum policy_mgr_con_mode.
|
|
# For example in GO+STA(5G) mode, when TPUT is onfigured as wlan system
|
|
# preference option, If 5G SCC needs higher priority than dbs, set it as 8.
|
|
g_prefer_5g_scc_to_dbs=8
|
|
|
|
END
|
|
|
|
# Note: Configuration parser would not read anything past the END marker
|
|
|